Process Data set: Jackopor Flamingo 80 Drænplade Denmark (en) en
Process information
| Key Data Set Information | |
| Location | DK |
| Geographical representativeness description | Denmark |
| Reference year | 2024 |
| Name |
|
| Technical purpose of product or process | Product variation and calculation of averages: - The insulation board is provided in several dimensions and thicknesses. Please use the conversion table in this EPD for other sizes and densities than the declared variant. Product description: - Expanded polystyrene (EPS) is a common material used for thermal insulation of buildings, including floors, walls and roofs. It is a polymer foam, consisting of air-filled polystyrene cells. As 98% of the material is air, EPS provides good insulating properties at a low weight. Other characteristics of the material include low moisture absorption, long service life, high compressive strength and 100% recyclable. - EPS is manufactured through permeating polystyrene beads with pentane, allowing the beads to expand when exposed to steam. This addition of a so-called blowing agent adds 4% - 6% w/w. The expanded polystyrene (EPS) beads are then fed into a block molding machine, where steam and pressure forms large blocks of EPS. The amount of EPS going into the mold determines the density of the block, where pressure class 80 (JP80) provides a compressive strength at 80 kN/m², which is approximately 15,0 kg/m³. After molding, the remaining blowing agent, pentane, is aired out and the blocks are cut into the desired shape. - The EPS boards used for exterior basement wall insulation are delivered with sharp edges, with grooves milled on one side, and covered with a non-woven fabric geotextile. - Weight per declared unit is 0,73 kg given a density of 15,0 kg/m³ with a thickness of 38 mm including non-woven fabric geotextile, glue and packaging material. |
| Classification |
Class name
:
Hierarchy level
|
| General comment on data set | Data quality: Specific data for the product composition are provided by the manufacturer. The data represent the production of the declared product and were collected for EPD development in the year of study. Background data is based on EPDs according to EN 15804 and different LCA databases. The data quality of the raw materials in A1 is presented in the table below. Allocation: The allocation is made in accordance with the provisions of EN 15804+A2. Incoming energy and water and waste production in-house is allocated equally among all products through mass allocation. Effects of primary production of recycled materials is allocated to the main product in which the material was used. The recycling process and transportation of the material is allocated to this analysis. Cut-off criteria: All major raw materials and all the essential energy is included. The production processes for raw materials and energy flows with very small amounts (less than 1%) are not included. These cut-off criteria do not apply for hazardous materials and substances. |
| Copyright | Yes |
| Owner of data set | |
| Quantitative reference | |
| Reference flow(s) |
|
| Biogenic carbon content |
|
| Time representativeness | |
| Data set valid until | 2029 |
| Time representativeness description | "2024-08-21" - "2029-08-21" |
| Technological representativeness | |
| Technology description including background system | The declared products are covered by harmonized technical specification DS/EN13163. Typical size: 600 x 2400 mm Typical thickness: 50 mm - 500 mm Thermal conductivity = 0,038 W/mK (EN 12667) Compressive strength at 10 % deformation, CS(10) = 80 kPa (EN 826) Durability of compressive strength against ageing and degradation, Compressive creep (2%), CC = 24 kPa (30% of CS(10)) - (DS/EN ISO 16534) Fire class (Reaction to fire): NPD (Euroclass F - EN 13501) Further technical information can be obtained on www.bewi.com and in the table below. |
Modelling and validation
| Subtype | specific dataset | ||||
| LCA methodology report | |||||
| Data sources, treatment and representativeness | |||||
| Documentation of data quality management | |||||
| Data source(s) used for this data set | |||||
| Completeness | |||||
| Validation | |||||
| |||||
| Compliance Declarations | |||||
| Compliance |
Compliance system name
EN 15804+A2
|
Approval of overall compliance
Fully compliant |
Nomenclature compliance
Fully compliant |
Methodological compliance
Fully compliant |
Review compliance
Fully compliant |
Documentation compliance
Fully compliant |
Quality compliance
Fully compliant |
| Compliance |
Compliance system name
|
Approval of overall compliance
Fully compliant |
Nomenclature compliance
Fully compliant |
Methodological compliance
Fully compliant |
Review compliance
Fully compliant |
Documentation compliance
Fully compliant |
Quality compliance
Fully compliant |
| Compliance |
Compliance system name
|
Approval of overall compliance
Fully compliant |
Nomenclature compliance
Fully compliant |
Methodological compliance
Fully compliant |
Review compliance
Fully compliant |
Documentation compliance
Fully compliant |
Quality compliance
Fully compliant |
Administrative information
| Data generator | |
| Data set generator / modeller |
|
| Data entry by | |
| Time stamp (last saved) | 2024-10-22T17:17:22 |
| Data set format(s) | |
| Publication and ownership | |
| UUID | 6b384413-87be-46d6-a9a3-d8bce74fbd5e |
| Date of last revision | 2024-08-22T13:46:16.8775498Z |
| Data set version | 00.04.000 |
| Registration authority | |
| Registration number | NEPD-7310-6699 |
| Owner of data set | |
| Copyright | Yes |
| License type | Free of charge for all users and uses |
| Access and use restrictions | None |
Environmental indicators
Indicators of life cycle