Process information
| Key Data Set Information | |
| Location | SE |
| Geographical representativeness description | Sweden |
| Reference year | 2025 |
| Name |
|
| Technical purpose of product or process | Product variation and calculation of averages The insulation board is provided in several dimensions and thicknesses. Please use the conversion table for other sizes than the declared unit. Product description Thermodren is a board which is for insulation and drainage outside on the cellar wall. The horisontal and vertical holes in the board makes sure that the water from the outside get into the holes and down into the drainage pipes. The holes also make sure that the cellar wall keeps dry. The board can also be delivered with a non voven textile to prevent small particles to clog up the holes. Thermodrän can also be used for on blue/green roofs and terrace. Expanded polystyrene (EPS) is a common material used for thermal insulation of buildings, including floors, walls and ceilings. It is a polymer foam, consisting of air-filled polystyrene cells. EPS is manufactured through permeating polystyrene beads with pentane, allowing the beads to expand when exposed to steam. This addition of a so-called blowing agent adds 4% - 6% w/w. The expanded polystyrene (EPS) beads are then fed into a block molding machine, where steam and pressure forms large blocks of EPS. The amount of EPS going into the mold determines the densitiy of the block, where pressure class 70 provides a density at 100 kN/m2, which is approximately 20 kg/m3. After molding, the remaining blowing agent, pentane, is aired out. Weight per declared unit is 0,76 kg given a density of 20 kg/cubic meter with a thickness of 38 mm. |
| Classification |
Class name
:
Hierarchy level
|
| General comment on data set | Data quality: Specific data for the product composition are provided by the manufacturer. The data represent the production of the declared product and were collected for EPD development in the year of study. Background data is based on EPDs according to EN 15804 and different LCA databases. The data quality of the raw materials in A1 is presented in the table below. Allocation: The allocation is made in accordance with the provisions of EN 15804+A2. Incoming energy and water and waste production in-house is allocated equally among all products through mass allocation. Effects of primary production of recycled materials is allocated to the main product in which the material was used. The recycling process and transportation of the material is allocated to this analysis. Cut-off criteria: All major raw materials and all the essential energy is included. The production processes for raw materials and energy flows with very small amounts (less than 1%) are not included. These cut-off criteria do not apply for hazardous materials and substances. |
| Copyright | Yes |
| Owner of data set | |
| Quantitative reference | |
| Reference flow(s) |
|
| Biogenic carbon content |
|
| Time representativeness | |
| Data set valid until | 2030 |
| Time representativeness description | 2025-05-15 - 2030-05-15 |
| Technological representativeness | |
| Technology description including background system | Typical size: 600 mm x 1200 mm Thickness: 100 mm and 200 mm Bending strength: >50 kN/m2 Drainage capacity: - 100mm: 60 l/min/m - 200mm 120 l/min/m |
Modelling and validation
| Subtype | specific dataset | ||||
| LCA methodology report | |||||
| Data sources, treatment and representativeness | |||||
| Documentation of data quality management | |||||
| Data source(s) used for this data set | |||||
| Completeness | |||||
| Validation | |||||
| |||||
| Compliance Declarations | |||||
| Compliance |
Compliance system name
EN 15804+A2
|
Approval of overall compliance
Fully compliant |
Nomenclature compliance
Fully compliant |
Methodological compliance
Fully compliant |
Review compliance
Fully compliant |
Documentation compliance
Fully compliant |
Quality compliance
Fully compliant |
| Compliance |
Compliance system name
|
Approval of overall compliance
Fully compliant |
Nomenclature compliance
Fully compliant |
Methodological compliance
Fully compliant |
Review compliance
Fully compliant |
Documentation compliance
Fully compliant |
Quality compliance
Fully compliant |
| Compliance |
Compliance system name
|
Approval of overall compliance
Fully compliant |
Nomenclature compliance
Fully compliant |
Methodological compliance
Fully compliant |
Review compliance
Fully compliant |
Documentation compliance
Fully compliant |
Quality compliance
Fully compliant |
Administrative information
| Data generator | |
| Data set generator / modeller |
|
| Data entry by | |
| Time stamp (last saved) | 2025-08-17T14:23:33 |
| Data set format(s) | |
| Publication and ownership | |
| UUID | 0ebd808b-9eec-4711-9157-2dcec8c47b3e |
| Date of last revision | 2025-05-14T14:35:25.6845861Z |
| Data set version | 00.03.000 |
| Registration authority | |
| Registration number | NEPD-11060-11009 |
| Owner of data set | |
| Copyright | Yes |
| License type | Free of charge for all users and uses |
| Access and use restrictions | None |
Environmental indicators
Indicators of life cycle